Graduate Theses & Dissertations

Pages

Heavy Rydberg Photo-dissociation Cross-section Calculations and Experimental Progress Towards Cold Collisions in Lithium
This thesis is divided into two parts, each of which supports constructing and using a lithium magneto-optical trap for cold collision studies: Part I One outgoing channel of interest from cold collisions is the production of ion pairs. We describe an effective method for calculating bound-to-continuum cross-sections for charged binary systems by examining transitions to states above the binding energy that become bound when the system is placed within an infinite spherical well. This approach is verified for ionization of a hydrogen atom, and is then applied to the heavy Rydberg system Li+...I-. Part II A wavemeter previously built in the lab is redesigned for increased reliability and ease of use by replacing the optical hardware with a rocker system, which can be aligned in mere minutes rather than half a day as was previously the case. The new wavemeter has been tested through saturated absorption spectroscopy of lithium. Author Keywords: cross-section, dissociation, lithium, magneto-optical trap, Michelson, wavemeter
Investigation of Using Phase Change Materials for Thermal Energy Storage in Adiabatic Compressed Air Energy Storage
There is an increasing global need for grid scale electrical energy storage to handle the implementation of intermittent renewable energy sources. Adiabatic compressed air energy storage is an emerging technology with similar performance to pumped hydro except it has the issue of heat loss during the compression stage. Previously, it has been considered to use sensible heat storage materials to store the heat created by compression in a thermal energy storage unit until energy is required, and then transfer the heat back to the air. This research proposes to instead use phase change materials to store the heat of compression, as this will reduce entropy generation and maximize roundtrip exergy efficiency. Different configurations and placements of the phase change materials are considered and exergy analyses are presented. The thermodynamic equations are derived and optimal setup conditions including amount of latent heat and melting temperatures are calculated. Author Keywords: Compressed Air Energy Storage, Energy Storage, Exergy, Phase Change Materials
"Multimodal Contrast" from the Multivariate Analysis of Hyperspectral CARS Images
The typical contrast mechanism employed in multimodal CARS microscopy involves the use of other nonlinear imaging modalities such as two-photon excitation fluorescence (TPEF) microscopy and second harmonic generation (SHG) microscopy to produce a molecule-specific pseudocolor image. In this work, I explore the use of unsupervised multivariate statistical analysis tools such as Principal Component Analysis (PCA) and Vertex Component Analysis (VCA) to provide better contrast using the hyperspectral CARS data alone. Using simulated CARS images, I investigate the effects of the quadratic dependence of CARS signal on concentration on the pixel clustering and classification and I find that a normalization step is necessary to improve pixel color assignment. Using an atherosclerotic rabbit aorta test image, I show that the VCA algorithm provides pseudocolor contrast that is comparable to multimodal imaging, thus showing that much of the information gleaned from a multimodal approach can be sufficiently extracted from the CARS hyperspectral stack itself. Author Keywords: Coherent Anti-Stokes Raman Scattering Microscopy, Hyperspectral Imaging, Multimodal Imaging, Multivariate Analysis, Principal Component Analysis, Vertex Component Analysis
Phosphoric Acid Chemically Activated Waste Wood
Activated Carbon (AC) is commonly produced by gasification, but there has been increasing interest in chemical activation due to its lower activation temperatures and higher yields. Phosphoric acid, in particular, succeeds in both these areas. Phosphoric acid activated carbon (PAC) can be environmentally sustainable, and economically favourable, when the phosphoric acid used in the activation is recycled. This thesis describes the digestion and activation of waste wood using phosphoric acid, as well as methods used to recover phosphoric acid, functionalize the produced activated carbon with iron salts and then test their efficacy on the adsorption of target analytes, selenite and selenate. In order to achieve an efficient phosphoric acid based chemical activation, further understanding of the activation process is needed. A two-step phosphoric acid activation process with waste wood feed stock was examined. The filtrate washes of the crude product and the surface composition of the produced PAC were characterized using X-ray Photoelectron Spectroscopy (XPS), Fourier Transform-Infrared spectroscopy (FT-IR), Ion Chromatography (IC), and 31P Nuclear Magnetic Resonance (NMR). XPS of the unwashed PAC contained 13.3 atomic percent phosphorous, as phosphoric acid, while the washed sample contained 1.4 atomic percent phosphorous as PO43-, and P2O74-. Using 31P NMR, phosphoric acid was identified as the primary phosphorous species in the acidic 0.1 M HCl washings, with pyrophosphates also appearing in the second 0.1 M NaOH neutralizing wash, and finally a weak signal from phosphates with an alkyl component also appearing in the DI wash. IC showed high concentrations of phosphoric acid in the 0.1 M HCl wash with progressively lower concentrations in both the NaOH and DI washes. Total phosphoric acid recovery was 96.7 % for waste wood activated with 25 % phosphoric acid, which is higher than previous literature findings for phosphoric acid activation. The surface areas of the PAC were in the 1500-1900 m2g-1 range. Both pre and post activation impregnation of iron salts resulted in iron uptake. Pre-activation resulted in only iron(III) speciation while post-activation impregnation of iron(II)chloride did result in iron(II) forming on the PAC surface. The pre-activated impregnated PAC showed little to no adsorption of selenite and selenate. The post-activation impregnated iron(II)chloride removed up to 12.45 ± 0.025 mg selenium per g Iron-PAC. Competitive ions such as sulfate and nitrate had little effect on selenium adsorption. Phosphate concentration did affect the uptake. At 250 ppm approximately 75 % of adsorption capacity of both the selenate and the selenite solutions was lost, although selenium was still preferentially adsorbed. Peak adsorption occurred between a pH of 4 and 11, with a complete loss of adsorption at a pH of 13. Author Keywords: Activated Carbon, doping, Iron, phosphoric acid, selenium
silicon sol-gel approach to the development of forensic blood substitutes
The research and development of synthetic blood substitutes is a reported need within the forensic community. This work contributes to the growing body of knowledge in bloodstain pattern analysis by offering a materials science approach to designing, producing and testing synthetic forensic blood substitutes. A key deliverable from this research is the creation of a robust silicon-based material using the solution-gelation technique that has been validated for controlled passive drip and spatter simulation. The work investigates the physical properties (viscosity, surface tension and density) of forensic blood substitute formulations and describes the similarity in the spreading dynamics of the optimized material to whole human blood. It then explores how blood and other fluids behave in impact simulation using high-speed video analysis and supports the use of the optimized material for spatter simulation. Finally, the work highlights the practical value of the material as an educational tool for both basic and advanced bloodstain experimentation and training. Author Keywords: bloodstain pattern analysis, forensic blood substitutes, high-speed video analysis, silicon solution-gelation chemistry, thin-film deposition, training and education
Extraction and Characterization of Hyaluronic Acid and Collagen from Eggshell Membrane Waste
Connecting academia to industry is one important way to advance towards meeting the United Nations (UN) Sustainability Goals (SDGs).1 Sustainability can be applied to all industrial sectors with the SDGs being implemented by 2030.2 This research contributes to the SDGs by investigating a way to remediate an industrial waste stream in the egg-breaking industry. If adopted, this would reduce the amount of eggshell membrane (ESM) waste placed in landfill where it does not decompose properly. The work described in this thesis specifically targets extraction of collagen and hyaluronic acid (HA), two components of the ESM that are of commercial value in the cosmetic, pharmaceutical, and biomedical industries3,4 . Deliverables from this research include economically viable extraction methods, developed based on green chemistry approaches, that can be transferred from lab bench to industrial scale. The extraction development process was guided by the 12 Principles of Green Chemistry5,6,7 and the 12 Principles of Green Engineering.8 HA was most successfully extracted using a sodium acetate solution on ground ESM. Filtrate was collected, exhaustively dialyzed and lyophilized. High molecular weight HA was recovered. Fourier transform infrared attenuated total reflectance (FTIR-ATR) spectroscopy and proton nuclear magnetic resonance (NMR) spectroscopy compared extracted material to reference HA identifying successful extraction. Collagen was extracted using acetic acid or pepsin enzyme digestion. Hydrophilic interaction liquid chromatography (HILIC) coupled with mass spectrometry (MS) compared amino acid composition of extracted materials to reference collagen material. FTIR-ATR spectra also supported successful extraction of collagen. This work identifies that HA and collagen can be conveniently extracted from ESM using an economical approach that can be implemented into egg-breaking facilities. This work highlights the benefits of connecting academia to industry to advance green chemical approaches while implementing sustainable practices into existing industry. Author Keywords: collagen, eggshell membrane waste, extraction, green chemistry, hyaluronic acid, sustainability
Adoption of a Finite Element Model of Material Deformation Relevant to Studying Corneal Biomechanics
The human cornea is required to exhibit specific material properties to maintain its regular shape under typical intraocular pressures which then allow for its correct optical functionality. In this thesis, the basis of continuum solid mechanics and the finite element method are introduced. We use finite element modelling to simulate the extension of an effective-1d, linear-elastic bar, a cornea-like body governed by Poisson’s equation, and the deformation of a loaded, linear-elastic, cube. Preliminary results for the deformation of a simulated, linear-elastic, cornea have also been achieved using the finite element approach. Author Keywords: continuum solid mechanics, corneal biomechanics, finite element method, intraocular pressure
Lipid-derived Thermoplastic Poly(ester urethane)s
Thermoplastic poly(ester urethane)s (TPEU)s derived from vegetable oils possess inferior physical properties compared to their entirely petroleum-based counterparts due to the structural limitations and lower reactivity of the precursor lipid-derived monomers. The present work shows that high molecular weight of TPEUs with enhanced performance can be obtained from lipid-derived monomers via (i) the synthesis of polyester diols with controlled molecular weights, (ii) the tuning of the functional group stoichiometry of the polyester diols and the diisocyanate during polymerization, (iii) the degree of polymerization (iv) the control of the hard segment hydrogen bond density and distribution via the use of a chain extender and (v) different polymerization protocols. Solvent-resistant TPEUs with high molecular weight displaying polyethylene-like behavior and controlled polyester and urethane segment phase separation were obtained. Structure-property investigations revealed that the thermal transition temperatures and tensile properties increased and eventually plateaued with increasing molecular weight. Novel segmented TPEUs possessed high phase separation and showed elastomeric properties such as low modulus and high elongation analogous to rubber. The response of the structurally optimized TPEUs to environmental degradation was also established by subjecting the TPEUs to hydrothermal ageing. TPEUs exhibited thermal and mechanical properties that were comparable to commercially available entirely petroleum-based counterparts, and that could be tuned in order to achieve enhanced physical properties and controlled degradability. Author Keywords: Hydrothermal degradation, Molecular weight control, Polyester diols, Renewable resources, Structure-property relationships, Thermoplastic poly(ester urethane)s
UV-Curable hybrid sol-gel materials
This thesis describes the synthesis, application and evaluation of a UV crosslinked 3-methacryloxypropyltrimethoxysilane-derived coating formulation. This is a two-component sol-gel system with 3-methacryloxypropyltrimethoxysilane (MaPTMS) and tetraethoxysilane (TEOS). Herein we show that if we change the co-solvent required for solubilizing MaPTMS from the more common methanol and ethanol to isopropanol we change the rate of hydrolysis from days or weeks to minutes. With the assistance of 2D 29Si-NMR we demonstrate that the system undergoes extensive condensation in twenty minutes. Using standard UV irradiation, the material can be extensively UV crosslinked with 70% of the methacryloxy functionality being consumed in 5 minutes upon irradiation in the presence of a photo-initiator. When this material is used to coat low carbon steel and immersed in an accelerated corrosion solution (dilute Harrison’s solution); this material affords low carbon steel 25 hours of protection when crosslinked and 17 hours of protection when uncrosslinked. The material was then used to encapsulate polyaniline (PANI), an intrinsic conductive polymer used in the corrosion protection of metal substrates. PANI has been encapsulated previously in sol-gel material, but due to the pH dependence of the solubility of PANI, it can not be encapsulated in more commonly chemically crosslinked sol-gel. As our system is UV crosslinked rather than chemically crosslinked, we were able to successfully demonstrate the inclusion of PANI into our coating system. Finally, this thesis includes a thorough computational investigation into the structure and band gap of PANI. Through the analysis of the band gap it was shown that the structure of the polymer commonly displayed in literature is not the correct structure of the polymer. Our results suggest that when PANI is made electrochemically, the oligomer contains two quinoid units next to one another instead of the more usually represented regularly alternating benzoid and quinoid units. The results also suggest that when PANI is made using the oxidant ammonium persulfate, the polymer most likely contains a Michael adduct structure somewhere in the polymer chain which dominates PANI’s electronic properties. Author Keywords: 3-Methacryloxypropyltrimethoxysilane, Computational Chemistry , Corrosion , Polyaniline, Tetraethoxysilane
Synthesis of Lipid Based Polyols from 1-butene Metathesized Palm Oil for Use in Polyurethane Foam Applications
This thesis explores the use of 1-butene cross metathesized palm oil (PMTAG) as a feedstock for preparation of polyols which can be used to prepare rigid and flexible polyurethane foams. PMTAG is advantageous over its precursor feedstock, palm oil, for synthesizing polyols, especially for the preparation of rigid foams, because of the reduction of dangling chain effects associated with the omega unsaturated fatty acids. 1-butene cross metathesis results in shortening of the unsaturated fatty acid moieties, with approximately half of the unsaturated fatty acids assuming terminal double bonds. It was shown that the associated terminal OH groups introduced through epoxidation and hydroxylation result in rigid foams with a compressive strength approximately 2.5 times higher than that of rigid foams from palm and soybean oil polyols. Up to 1.5 times improvement in the compressive strength value of the rigid foams from the PMTAG polyol was further obtained following dry and/or solvent assisted fractionation of PMTAG in order to reduce the dangling chain effects associated with the saturated components of the PMTAG. Flexible foams with excellent recovery was achieved from the polyols of PMTAG and the high olein fraction of PMTAG indicating that these bio-derived polyurethane foams may be suitable for flexible foam applications. PMTAG polyols with controlled OH values prepared via an optimized green solvent free synthetic strategy provided flexible foams with lower compressive strength and higher recovery; i.e., better flexible foam potential compared to the PMTAG derived foams with non-controlled OH values. Overall, this study has revealed that the dangling chain issues of vegetable oils can be addressed in part using appropriate chemical and physical modification techniques such as cross metathesis and fractionation, respectively. In fact, the rigidity and the compressive strength of the polyurethane foams were in very close agreement with the percentage of terminal hydroxyl and OH value of the polyol. The results obtained from the study can be used to convert PMTAG like materials into industrially valuable materials. Author Keywords: Compressive Strength, Cross Metathesis, Fractionation, Polyols, Polyurethane Foams, Vegetable Oils
Novel Aliphatic Lipid-Based Diesters for use in Lubricant Formulations
Structure-property relationships are increasingly valued for the identification of specifically engineered materials with properties optimized for targeted application(s). In this work, linear and branched diesters for use in lubricant formulations are prepared from lipid-based oleochemicals and their structure-property relationships reported. It is shown that the branched diesters possess exceptional physical property profiles, including suppression of crystallization, and are superior alternatives for use in lubricant formulations. For the linear aliphatic diesters, both high and low temperature properties were predictable functions of total chain length, and both were differently influenced by the fatty acid versus diol chain length. Symmetry did not influence either, although thermal stability decreased and thermal transition temperatures increased with increasing saturation. All of the linear diesters demonstrated Newtonian flow behaviour. Viscosity was also predictable as a function of total chain length; any microstructural features due to structural effects were superseded by mass effects. Author Keywords: Crystallization, Phase behaviour, Rheology, Structure-Function, Thermogravimetric analysis, Vegetable Oils
Advanced broadband CARS microscopy based on a supercontinuum-generating photonic crystal fiber
I have developed and improved a coherent anti-Stokes Raman scattering (CARS) microscope based on the spectral focusing (SF) technique. The CARS microscope uses an 800 nm oscillator and a photonic crystal fibre module to generate the supercontinuum Stokes. The photonic crystal fibre was originally designed to generate light beyond 945 nm which is useful for CARS microscopy in the CH/OH frequencies but essentially prevents access to the important fingerprint region at lower frequencies. With expert and nontraditional approaches to generating supercontinuum with sufficient power at wavelengths below 945 nm, I substantially extend the usefulness of the module for SF-CARS microscopy deep into the fingerprint region. Moreover, with the invention of a dynamic supercontinuum generation scheme we call "spectral surfing," I improve both the brightness of the CARS signal and extend the accessible CARS frequency range to frequencies as low as 350 cm$^{-1}$ and as high as 3500 cm$^{-1}$---all in a single scan-window. I demonstrate the capabilities of our broadband SF-CARS system through CARS and four-wave mixing hyperspectroscopy on samples such as astaxanthin, lily pollen and glass; liquid chemicals such as benzonitrile, nitrobenzene and dimethyl sulfoxide; and on pharmaceutical samples such as acetaminophen, ibuprofen, and cetirizine. Furthermore, In search of more useful Stokes supercontinuum sources, I compare the performance of two commercial photonic crystal fibre modules for use in SF-CARS applications, ultimately finding that one module provides better spectral characteristics for static supercontinuum use, while the other provides improved characteristics when spectral surfing is implemented. Author Keywords: coherent anti-Stokes Raman scattering, nonlinear microscopy, scanning microscopy, spectroscopy, supercontinuum generation, vibrational spectroscopy

Pages

Search Our Digital Collections

Query

Enabled Filters

  • (-) = Materials Science

Filter Results

Date

2004 - 2024
(decades)
Specify date range: Show
Format: 2024/03/28